Keg Sizes Chart: Half Barrel, Sixth Barrel, Gallons and Pints per Keg
Keg sizes chart with gallons, liters, dimensions, full weight and pints per keg, plus couplers, cooler capacities, deposits and used kegerator checks.
A US half barrel keg holds 15.5 gallons, or 124 16-ounce pints, a quarter barrel holds 7.75 gallons (62 pints), and a sixth barrel holds about 5.16 gallons (41 pints). Those sizes are fractions of the 31-gallon US beer barrel. Volume is close to standard, but outside dimensions and weights vary by keg maker, so measure before you commit to a cooler.
Keg size chart
| Keg | Other names | Gallons | Liters | Height x diameter (in) | Full weight, lb (BA / Micro Matic) | 16 oz pints | 12 oz servings |
|---|---|---|---|---|---|---|---|
| Half barrel | Full-size keg | 15.5 | 58.67 | 23.3 x 17.0 | 161 / 160.7 | 124 | 165 |
| 50 liter | Euro keg | 13.2 | 50 | 20.2 x 17.0 | 137 / 133 | 105 | 140 |
| Quarter barrel | Pony keg | 7.75 | 29.34 | 14.8 x 17.0 | 87 / 83.3 | 62 | 82 |
| Slim quarter | Slim 30 | 7.75 | 29.34 | 23.3 x 11.0 | 87 / 81.87 | 62 | 82 |
| Sixth barrel | Cylinder | 5.16 | 19.55 | 23.3 x 9.25 | 58 / 55.5 | 41 | 55 |
| Cornelius (ball lock) | Home brew tank | 5.0 | 18.93 | 23 x 9 | See note | 40 | 53 |
Gallons and the first weight come from the Brewers Association (BA) Draught Beer Quality Manual, fourth edition, which lists two quarter barrels at 87 pounds without calling either one slim. Dimensions come from Micro Matic's keg chart and liters from KegWorks. Cornelius kegs aren't on the BA or Micro Matic charts: KegWorks lists 23 x 9 inches and 55 pounds full, and MoreBeer lists 49 pounds. Serving counts are our math, shown below.
How is a keg size defined?
Federal rules set the unit. 27 CFR 25.11 defines a barrel, as a unit of measure, as 31 US gallons, and TTB's beer FAQ says the same. 27 CFR 25.156 authorizes kegs rated at whole barrels, halves, thirds, quarters, sixths and eighths, plus 5 gallon, 30 liter and 50 liter sizes.
So 31 / 2 = 15.5 gallons and 31 / 4 = 7.75. A sixth works out to 5.167 gallons, and sources differ: BA prints 5.16, one Micro Matic page says 5.17, and its chart says 5.23 gallons but 640 ounces, which is 5 gallons. Since the CFR also lists a separate 5 gallon size, ask which rating a keg carries if the difference matters.
How many pints are in a keg?
Multiply gallons by 128 ounces, then divide by the serving size. The main chart rounds down to whole servings.
| Keg | Gallons x 128 = oz | / 16 oz | / 12 oz |
|---|---|---|---|
| Half barrel | 15.5 x 128 = 1,984 | 124 | 165.3 |
| 50 liter | 13.2 x 128 = 1,689.6 | 105.6 | 140.8 |
| Quarter or slim quarter | 7.75 x 128 = 992 | 62 | 82.7 |
| Sixth barrel | 5.16 x 128 = 660.5 | 41.3 | 55 |
| Cornelius | 5 x 128 = 640 | 40 | 53.3 |
This is straight volume with nothing subtracted for foam or waste. None of the sources we opened publishes a standard loss percentage, so any figure is your own assumption: at an assumed 10 percent, 124 pints becomes about 111. Published counts can also differ from the math. West Sixth Brewing lists around 125 pours for a half barrel and around 50 for a sixth, defining a pour as a pint with about 2 ounces of head, so ask how any quoted count was figured. For small measures, see shot glass sizes.
Why do keg dimensions differ between charts?
Micro Matic's chart says capacities, dimensions and weights can vary between manufacturers, and published numbers show it:
| Keg | Micro Matic (in) | KegWorks (in) | West Sixth Brewing (in) |
|---|---|---|---|
| Half barrel, height x diameter | 23.3 x 17.0 | 23 3/8 x 16 1/8 | 23.62 x 15.55 |
| Quarter barrel, height x diameter | 14.8 x 17.0 | 13 7/8 x 16 1/8 | Not listed |
| Slim quarter, height x diameter | 23.3 x 11.0 | 23 3/8 x 11 1/8 | Not listed |
| Sixth barrel, height x diameter | 23.3 x 9.25 | 23 3/8 x 9 1/4 | 23.62 x 8.98 |
| 50 liter, height x diameter | 20.2 x 17.0 | 20.94 x 16.06 | Not listed |
Micro Matic also says quarter kegs come in rubber-sided and bulged versions with a slightly larger 17 inch diameter. Our inference: plan around 17 inches unless you know the exact keg.
Empty weights on Micro Matic's chart are 29.7 pounds for a half barrel, 28.5 for 50 liter, 17.3 for a quarter, 16 for a slim quarter and 13.76 for a sixth. BA recommends a buddy lift or mechanical lifting system when moving kegs.
Which kegs fit which cooler?
Use the capacity on the model's own sheet. Most of these list only half barrels.
| Model | Type | Published keg capacity | Cabinet W x D x H (in) |
|---|---|---|---|
| True TDD-1-HC | Kegerator | 1 half barrel | 23 1/2 x 30 1/4 x 38 1/2 |
| True TDD-2-HC | Kegerator | 2 half barrels | 58 7/8 x 27 1/8 x 37 |
| True TDD-3-HC | Kegerator | 3 half barrels | 69 1/8 x 27 1/8 x 37 |
| Avantco UDD-1-HC-S | Kegerator | 1 half, 2 quarter or 4 sixth | 23 1/2 x 30 1/4 x 39 3/4 |
| Micro Matic MDD23D-E | Kegerator | 1 half, 1 quarter or 4 sixth | Not on page |
| True TBB-2-HC | Back bar | 2 half barrels | 58 7/8 x 27 3/4 x 37 |
| True TBB-24-48-HC | Back bar | 2 half barrels | 49 1/8 x 24 1/2 x 35 5/8 |
| Beverage-Air BB48HC-1-F-S-27 | Back bar | 2 half kegs | 48 x 24 1/2 x 36 |
| Beverage-Air BB48HC-S | Back bar | 2 straight wall kegs | 48 x 30 3/8 x 34 |
True's TDD heights exclude 15 3/4 inches for the draft arm, and Avantco lists 55 3/4 inches overall. A dealer page for Micro Matic's MDD23-E adds up to 2 slim quarters or 4 home brew tanks. True says the TDD line accommodates all types of beer kegs but publishes capacity only in half barrels, so confirm other sizes. See commercial refrigerator sizes for more back bar data.
The capacity number doesn't cover three things:
- Height above the keg. Micro Matic recommends at least 5 to 6 inches above the keg for the coupler and hose, 4 inches with an elbow fitting, or 1 inch with a low-profile coupler. By our math a 23.3 inch keg needs 28.3 to 29.3 inches with a standard setup. Avantco lists 28 5/8 inches of interior height and the BB48HC-1-F-S-27 lists 29 1/2.
- Door opening. The BB48HC-1-F-S-27 door opening is 16 1/2 x 27 7/8 inches. By our math, a 16 1/8 inch keg clears it and a 17 inch keg doesn't, and the sheet doesn't say which half keg its 2-keg rating assumes.
- Draft readiness. The back bar sheets above don't mention a draft tower or column, so we'd treat those figures as storage capacity. Micro Matic says dispensing from more than one keg needs more faucets or a tower adapter.
What coupler does a keg need?
The coupler must match the keg valve, and Micro Matic calls the D system the most common in the US. It lists these systems and example brands:
| System | Also called or named after | Brands Micro Matic names |
|---|---|---|
| D | American Sankey | Anheuser-Busch, Miller, Molson-Coors, Labatt, most craft breweries |
| S | European Sankey | Heineken, Becks, Amstel Light, Pilsner Urquell |
| A | German Slider | Hoegaarden, Paulaner, Spaten, Warsteiner |
| M | None listed | Schneider, Aventinus, Einbecker |
| G | Grundy | Bass, Boddington's, Caffrey's, Anchor Steam (50 liter kegs) |
| U | UEC | Guinness, Harp |
| Home brew | Ball lock | Cornelius tanks |
Micro Matic also lists Twin Probe and KeyKeg systems, and says its brand data is subject to change, so confirm with your distributor. KegWorks warns that imported 50 liter kegs don't use a standard D coupler.
How cold should kegs be stored?
BA's manual says beer should be stored between 34°F and 38°F, and that even a few degrees above 38°F can cause excessive foaming. Its tables show a 38°F keg reaching 45°F after five hours, and a 44°F keg needing 18 hours in the cooler to get back to 38°F.
Who owns the keg, and what does the deposit cover?
Usually the brewer. BA says kegs are always the property of the brewery that bought and filled them, and that a deposit doesn't convey title. Deposits usually run about 15 to 20 percent of replacement cost, per BA, and exist to encourage return. West Sixth Brewing, for one, charges $30 a keg, lifted on return.
Don't resell a deposit keg or list one with a kegerator. BA says returning a keg to its owner is the right thing to do and points to KegReturn.com. It also notes that possession of stolen property is illegal in all 50 states and that state scrap laws vary widely. BA's manual adds that keg valves should never be removed in the field.
What should you check on a used kegerator?
Food Service Surplus connects buyers and sellers. The platform doesn't inspect, test, ship or guarantee equipment, so get these answers from the seller. Buying used restaurant equipment covers the broader process.
- Tower. Count faucets and confirm the tower fits under any shelf. True and Micro Matic both move cold air into the column, so ask whether that still works.
- Regulator. BA says a primary regulator must contain a safety relief valve, since bottled CO2 can exceed 1,000 psi. We'd budget to replace one of unknown history.
- CO2 tank. Ask who owns it. BA notes vendors may deliver, swap and inspect cylinders, so a tank may not be the seller's to sell (our inference). BA also says tanks should never sit inside the refrigerator, because a leak can fill the space with deadly CO2. Avantco and Micro Matic describe knockouts for an outside gas line. Micro Matic says a 5 pound tank dispenses 5 to 7 kegs.
- Coupler. Confirm the system matches your kegs. Avantco includes one D coupler, while Micro Matic says tapping equipment isn't included. BA says a coupler should contain a pressure relief valve, tested periodically.
- Beer lines. BA says vinyl tubing should be replaced every one to two years and lines cleaned at least every two weeks. Ask when they were last replaced.
- Holding temperature. Published ranges are 33 to 38°F for True's TDD models, 33 to 40°F for Avantco and 36 to 38°F for Micro Matic. True says to run a unit empty for 24 hours before loading to verify operation.
- Moving. True says a unit laid on its side or back should stand upright for twice that time, up to 4 hours, or 24 hours if it was down longer, before power goes on. Check the path with the equipment doorway fit calculator.
Browse used beverage equipment, used commercial refrigeration or all restaurant equipment. The bar equipment list covers the rest of the setup.
Seller checklist for listing a kegerator
- Brand and full model string from the nameplate, with a photo.
- Published keg capacity and measured interior height, width and depth.
- Faucet count and overall height with the tower on.
- Coupler system, such as D, and how many are included.
- Regulator and CO2 tank: included or not, and whether you own the tank.
- Age of the beer lines, if known.
- Whether it's running, and the current thermometer reading.
- Voltage, amps and plug from the label.
- Pickup location and whether the unit has been tipped.
- No kegs in the sale unless you hold clear title.
List through sell used restaurant equipment.
Frequently asked questions
How many gallons are in a full-size keg?
A half barrel, which BA calls a full-size keg, holds 15.5 gallons. That's half of the 31-gallon barrel in federal regulations.
How many pints are in a keg?
By straight division, 124 16-ounce pints in a half barrel, 62 in a quarter barrel and 41 in a sixth barrel, with nothing subtracted for foam or waste.
What is a pony keg?
BA and Micro Matic both use pony keg for a quarter barrel, which holds 7.75 gallons. Micro Matic lists a standard quarter at 14.8 inches tall and 17 inches in diameter.
How much does a full keg weigh?
BA's chart lists 161 pounds for a half barrel, 87 for a quarter and 58 for a sixth. Micro Matic lists slightly less.
Is a sixth barrel the same as a Cornelius keg?
No. A sixth barrel is about 5.16 gallons and taps with a coupler matched to its valve, while a Cornelius tank holds 5 gallons and uses ball lock or, on some older models, pin lock fittings.
Can I sell an empty keg I paid a deposit on?
BA says a deposit doesn't convey title, so the keg still belongs to the brewery. Return it to the retailer, wholesaler or brewery instead.
Sources
Dates are the revision shown on each document. Specifications can change, so check the sheet for the exact unit. The Avantco and BB48HC-1-F-S-27 sheets are hosted by dealers, and the Micro Matic MDD23-E detail comes from a dealer page.
- Government: 27 CFR 25.11 definitions, 2024 edition (PDF), 27 CFR 25.156 keg beer, 2024 edition (PDF) and TTB beer FAQs
- Brewers Association: Draught Beer Quality Manual, fourth edition (PDF) and Keg Etiquette
- Micro Matic: draft beer keg sizes and its keg chart image, keg tapping information, beer brand and coupler listing, basic draft system components and MDD23D-E kegerator
- Keg charts: KegWorks guide to keg sizes and MoreBeer keg sizes
- Brewery: West Sixth Brewing keg sales information
- True: TDD-1-HC (6/25), TDD-2-HC (6/20), TDD-3-HC (6/20), TBB-2-HC (6/20), TBB-24-48-HC (6/20) and quick start manual
- Beverage-Air: BB48HC-1-F-S-27 spec sheet and BB48HC-S product page
- Avantco: UDD-1-HC-S spec sheet
- Dealer page: Micro Matic MDD23-E at BBS Pro
Related guides
- Bar Equipment List: Underbar, Refrigeration and Glassware Checklist
A bar equipment list with maker specs for ice bins, bar sinks, glass washers, back bar coolers and draft, plus FDA Food Code items and used-buying checks.
- Coffee Shop Equipment List: What You Need, New or Used
A coffee shop equipment list with maker specs for espresso machines, grinders and brewers, utilities to plan first and what to check on used pieces.
- Commercial Refrigerator Sizes: Reach-In, Undercounter, Prep and Back Bar
Commercial refrigerator sizes from manufacturer spec sheets: reach-in, undercounter, chef base, prep and back bar dimensions, plus clearances and plugs.