Commercial Refrigerator Sizes: Reach-In, Undercounter, Prep and Back Bar

Commercial refrigerator sizes from manufacturer spec sheets: reach-in, undercounter, chef base, prep and back bar dimensions, plus clearances and plugs.

By Food Service SurplusPublished 16 min read
Buyer guideEquipment

There is no single standard size for a commercial refrigerator. Each manufacturer publishes its own dimensions, and the same brand can change depth or height between versions of one model. The chart below shows what published spec sheets list for common types. Use it to narrow your search, then confirm the exact model number before you measure a doorway or a kitchen wall.

Type Example models Published width x depth x height (in)
One-section reach-in True T-23-HC; Atosa MBF8505GR 27 x 29 1/2 x 78 3/8; 27 x 31 7/10 x 83 1/10
Two-section reach-in True T-49-HC; Atosa MBF8507GR 54 1/8 x 29 1/2 x 78 3/8; 54 2/5 x 31 7/10 x 83 1/10
Three-section reach-in True T-72-HC; Atosa MBF8508GR 78 1/8 x 29 1/2 x 78 3/8; 81 9/10 x 31 7/10 x 83 1/10
Undercounter True TUC-27-HC; True TUC-48-HC 27 5/8 x 30 1/8 x 29 7/8; 48 3/8 x 30 1/8 x 29 3/4
Chef base True TRCB-52-HC; Atosa MGF8451GR 51 7/8 x 32 1/8 x 20 1/2; 52 x 33 x 26 3/5
Pizza prep table True TPP-AT-60-HC 60 1/4 x 33 5/8 x 38 7/8
Glass door merchandiser True GDM-49-HC~TSL01; Turbo Air TGM-50RS(B)-N 54 1/8 x 29 7/8 x 78 5/8; 55 7/8 x 32 x 78 1/2
Back bar cooler True TBB-2-HC; Beverage-Air BB48HC-S 58 7/8 x 27 3/4 x 37; 48 x 30 3/8 x 34

Published numbers don't always measure the same thing. True's reach-in, undercounter, worktop, chef base and prep sheets give heights without casters, while Traulsen's includes them, so two units with similar listed heights can differ by several inches on the floor. The notes in each table below say what each manufacturer leaves out.

How big are reach-in refrigerators?

The sheets below cover full-height models with one, two or three sections. Capacity appears only where the manufacturer's sheet gives it.

Model Sections / doors W x D x H (in) Net capacity (cu ft) What the sheet says about the numbers
True T-23-HC 1 / 1 27 x 29 1/2 x 78 3/8 Not on sheet Height excludes 5 in. for casters
Atosa MBF8505GR 1 / 1 27 x 31 7/10 x 83 1/10 19.1 4 in. casters listed; not stated whether height includes them
True T-49-HC 2 / 2 54 1/8 x 29 1/2 x 78 3/8 Not on sheet Height excludes 5 in. for casters
Turbo Air M3R47-2-N-AL / -AR 2 / 2 51 3/4 x 30 3/4 x 78 42.3 Depth excludes 3 in. rear condensate enclosure; height excludes 5 in. for casters
Traulsen G20010-032 2 / 2 52 1/8 x 35 x 83 7/16 46.02 Height is on standard 6 in. casters; depth over the body is 32 in.
Atosa MBF8507GR 2 / 2 54 2/5 x 31 7/10 x 83 1/10 43.8 4 in. casters listed; not stated whether height includes them
True T-72-HC 3 / 3 78 1/8 x 29 1/2 x 78 3/8 Not on sheet Height excludes 5 in. for casters
Atosa MBF8508GR 3 / 3 81 9/10 x 31 7/10 x 83 1/10 68 4 in. casters listed; not stated whether height includes them

A True T-49-HC on its standard casters is about 83 3/8 inches tall (78 3/8 plus 5). The Turbo Air sheet's side view shows the same arithmetic: 78 inches plus 5 for casters reaches 83.

What do the numbers 23, 49 and 72 mean?

They aren't widths. The T-23-HC, T-49-HC and T-72-HC are 27, 54 1/8 and 78 1/8 inches wide. It would be natural to read the numbers as cubic feet, but True's current sheets for these three models list no cubic foot figure, and we couldn't find a True statement explaining the naming. Treat the number as a series name, not a spec.

Other brands show why that matters. Turbo Air's M3R47-2-N-AL has a 47 in its name and lists 42.3 net cubic feet. Atosa's MBF8507GR lists 43.8 cubic feet and 54 2/5 inches of width, and neither figure appears in its model number.

Suffixes can change the box too. "HC" on True's sheets marks a hydrocarbon refrigerant model. "~SPEC3" marks Spec Package 3, and it isn't only a cosmetic change: the TUC-48-HC is listed at 30 1/8 inches deep, while the TUC-48-HC~SPEC3 is 29 1/8 inches before an extra 1 1/2 inches for door handles. Copy the whole model string from the nameplate.

What sizes do undercounter and worktop refrigerators come in?

Model Doors W x D x H (in) Net capacity (cu ft)
True TUC-27-HC 1 27 5/8 x 30 1/8 x 29 7/8 Not on sheet
True TUC-48-HC 2 48 3/8 x 30 1/8 x 29 3/4 Not on sheet
True TWT-27-HC (worktop) 1 27 5/8 x 30 1/8 x 33 3/8 Not on sheet
True TWT-48-HC (worktop) 2 48 3/8 x 30 1/8 x 33 3/8 Not on sheet
Atosa MGF8401GR 1 27 1/2 x 30 x 34 1/2 7.2
Atosa MGF8402GR 2 48 1/4 x 30 x 34 1/2 13.4
Atosa MGF8403GR 2 60 1/4 x 30 x 34 1/2 17.2

True's undercounter and worktop heights exclude 6 1/4 inches for casters or 6 inches for optional legs, and depth excludes 1 inch for rear bumpers, plus 1/4 inch for a front bumper on the TWT-48-HC. Atosa's spec sheet lists the MGF8401GR at 34 1/2 inches high, but its MGF8401GRL product page shows 34 1/5, so measure before relying on that height. With standard casters, a TUC-27-HC stands about 36 1/8 inches tall and a TWT-27-HC about 39 5/8 inches. If a unit has to fit under an existing counter, check the height with the casters or legs it will actually use. True lists 2 1/2 inch casters as an option on the TUC-27-HC and both TWT models.

How big is a chef base?

A chef base is a low refrigerated drawer unit with a reinforced top built to carry cooking equipment. That makes height and top load matter more than interior volume.

Model Drawers W x D x H (in) Capacity (cu ft) Food pans (per sheet)
True TRCB-52-HC 2 51 7/8 x 32 1/8 x 20 1/2 Not on sheet 3 full-size 12 x 20 x 4 in. per drawer, sold separately
Atosa MGF8450GR 2 48 2/5 x 33 x 26 3/5 7.7 4 x 12x20 and 6 x 1/6
Atosa MGF8451GR 2 52 x 33 x 26 3/5 8.4 6 x 12x20
Atosa MGF8453GR 4 72 1/2 x 33 x 26 3/5 12.1 8 x 12x20

True's TRCB-52-HC height excludes 5 inches for casters, which makes about 25 1/2 inches on the floor, and depth excludes 1 inch for rear bumpers. True rates the top for up to 717 pounds. It also requires at least 4 inches between the bottom of a countertop cooking appliance's heating element and the chef base top, says failing to provide that voids the warranty, and recommends a heat shield. Check your line equipment's legs before you buy.

How big are sandwich and pizza prep tables?

Model Doors Top pans W x D x H (in) Excludes
True TSSU-48-12-HC (sandwich/salad) 2 12 48 3/8 x 30 1/8 x 36 3/4 1 in. rear bumpers; 6 1/4 in. casters
True TPP-AT-60-HC (pizza) 2 8 60 1/4 x 33 5/8 x 38 7/8 1 in. rear bumpers; 1 3/4 in. cutting board; 5 3/4 in. casters

Add it up for a tight line. The TPP-AT-60-HC reaches about 36 3/8 inches deep with bumpers and cutting board, and about 44 5/8 inches tall on standard casters.

How big are glass door merchandisers?

Model Doors W x D x H (in) Net capacity (cu ft) Excludes
True GDM-49-HC~TSL01 2 54 1/8 x 29 7/8 x 78 5/8 Not on sheet 1 5/8 in. door handles
Turbo Air TGM-50RS(B)-N 2 55 7/8 x 32 x 78 1/2 45.97 1 3/8 in. door handle
Atosa MCF8722GR 1 27 x 31 1/2 x 81 1/5 19.4 Not stated
Atosa MCF8723GR 2 54 2/5 x 31 1/2 x 81 1/5 43.8 Not stated
Atosa MCF8724GR 3 81 9/10 x 31 1/2 x 81 1/5 69.5 Not stated

Turbo Air also lists bottle capacity for the TGM-50RS(B)-N: 560 12-ounce bottles full, or 448 to the load line.

How big are back bar coolers?

Check depth first, because it can vary a lot within one model family.

Model Doors W x D x H (in) Published capacity
True TBB-24-48-HC 2 49 1/8 x 24 1/2 x 35 5/8 48 six-packs of 12 oz cans; 2 half barrels
True TBB-2-HC 2 58 7/8 x 27 3/4 x 37 88 six-packs of 12 oz cans; 2 half barrels
Beverage-Air BB48HC-1-F-S-27 2 48 x 24 1/2 x 36 12.4 cu ft net; 2 half kegs
Beverage-Air BB48HC-S 2 48 x 30 3/8 x 34 15.139 cu ft net; 2 straight wall kegs
Glastender C1SL48 (low-profile bar cooler) 2 48 x 24.13 x 29 10.3 long neck cases; 84 750 ml bottles

Both Beverage-Air units are nominally 48 inches wide, but they differ by nearly 6 inches in depth. True's depths exclude 1 inch for rear bumpers. Glastender lists the C1SL48 under bar refrigeration as a side-serviced, low-profile cooler rather than calling it a back bar, so check that the service side suits your layout.

How should you pick a size?

We didn't find a manufacturer-published rule that converts seats or covers into cubic feet, so this guide doesn't offer one. These checks use published data instead:

  • Start with what goes inside. True's T-49-HC shelves are 24 9/16 x 22 3/8 inches, and Turbo Air's M3R47-2-N-AL shelves are 23 x 23 1/2 inches. Compare those with your boxes and pans.
  • Check rack options if you use sheet pans. True's full-door rack for the T-49-HC holds up to 22 pans of 18 x 26 inches. Turbo Air's full-door rack for the M3R47-2-N-AL holds up to 15.
  • Count pans for drawer and prep units. True and Atosa list pan counts for the chef bases above, and True lists top pan counts for its prep tables.
  • Don't assume all listed volume is usable. True warns against product pressing on the sides or back wall or coming within 4 inches of the evaporator housing.

The commercial kitchen equipment checklist can help you plan the rest of the line.

How much clearance does a commercial refrigerator need?

It depends on the model family, and the minimums can be zero on some sides. True's quick start manual (February 2026) lists these:

True model family Top (in) Sides (in) Back (in)
T-Series refrigerator 0 0 1
T-Series freezer 3 0 3
GDM refrigerator (general row; True lists some models, such as GDM-05, GDM-09 and GDM-10, separately) 0 0 1
TUC / TWT 0 0 0
TPP / TSSU N/A 0 0
TRCB 1 1 1
TBB 1 1 1
Spec Series 12, open 0 1

True states that the warranty is void if ventilation is insufficient, and says to keep ventilation openings clear. Other brands differ. Traulsen's G20010-032 sheet requires 12 inches above the cabinet. The Atosa, Turbo Air and Beverage-Air sheets used here give no clearance figures, so get those from the model's manual. True's TUC-27-HC sheet describes that unit as front breathing. Don't apply True's zero-clearance figures to another brand without checking.

How much do doors, casters and plugs add?

Door swing. A door needs aisle space that the cabinet depth doesn't show. Traulsen's G20010-032 is 35 inches deep overall and 57 5/8 inches with a door open to 90 degrees. Beverage-Air's BB48HC-1-F-S-27 goes from 24 1/2 to 41 3/8 inches. Hinging is often a choice: Turbo Air's -AL and -AR versions hinge all left or all right, Atosa lists a left-hand hinge version of its MGF8401GR (the MGF8401GRL), True offers factory alternate hinging as an option, and Beverage-Air lists field-reversible doors, with the hinge kit not included.

Power. Every True, Turbo Air, Traulsen and Beverage-Air sheet used here that lists a plug shows 115/60/1 with a NEMA 5-15P, so these are ordinary 15-amp cord-and-plug units. Amps vary: 2.0 for the TUC-27-HC, 2.2 for the T-23-HC, 5.4 for the T-49-HC, 6.9 for the T-72-HC and 7.9 for the Traulsen G20010-032. Cords are short, from 7 feet on True's TBB sheets to 10 feet on its TUC sheets. True's T-49-HC sheet calls for a dedicated 15-amp outlet, and its manual says to always use an individual dedicated circuit. Some True models also have 220-240 volt export versions, so read the nameplate on a used unit.

Will it fit through the door?

Compare the unit's smallest dimensions with the clear opening of every door on the path, plus any handles, bumpers or casters the sheet leaves out. A T-49-HC is 54 1/8 inches wide, so unless the opening is wider than that, it has to pass depth first, at 29 1/2 inches plus whatever else projects. Crated units are bigger: Traulsen lists 62 x 42 x 85 inches for the G20010-032 crate, and Beverage-Air lists 50 x 27 x 43 inches for the BB48HC-1-F-S-27.

The equipment doorway fit calculator takes the unit size and each door and elevator opening, then tells you whether it fits upright, only tipped, or not at all.

If tipping is the only way through, check the manufacturer's moving instructions first. True's manual says a unit laid on its back or side should stand upright for twice the time it was down, up to 4 hours, and for 24 hours if it was down longer than that, before it is powered on. It also warns of tip-over and says to run the unit empty for 24 hours before loading.

What should you verify on a used or new/open-box unit?

Food Service Surplus connects buyers and sellers. The platform doesn't inspect, test, ship or guarantee equipment, so get these answers from the seller and check them yourself where you can. Buying used restaurant equipment covers inspection and pickup in more detail.

  • Nameplate photo. Get the model and serial number from the label. True says label location varies by model, and it offers a serial number lookup on its site.
  • Refrigerant. True says to check the serial label to identify it. Hydrocarbon refrigerant is flammable, and True says servicing must be done by qualified technicians.
  • Electrical match. Compare the label's voltage and amps with your circuit.
  • Gaskets. Ask for close-up photos. True's maintenance list calls for checking gasket condition and whether gaskets seal correctly.
  • Holding temperature. Published ranges vary: 33 to 38°F for the True T-49-HC, 35 to 38°F for Atosa's MBF series, 34 to 38°F for the Traulsen G20010-032, and 36 to 38°F for the Beverage-Air BB48HC-1-F-S-27. Ask to see the unit running with its own thermometer reading, or plan to test it before loading. True's manual says its units aren't for potentially hazardous foods with the control set above 41°F.
  • Included parts. Casters or legs, shelves and clips, racks, cutting boards and pans. Some are sold separately even when new.
  • Measured dimensions. Ask for width, depth and height as the unit stands today.

Browse used commercial refrigerators, used commercial freezers, all used commercial refrigeration or the full restaurant equipment category.

Seller checklist for listing commercial refrigeration

Buyers need to know whether a unit fits their space, so give exact numbers:

  • Brand and the full model string from the nameplate, with a photo.
  • Measured width, depth and height, and whether casters, legs and handles are included.
  • Door or drawer count, hinge side, and shelf or pan count.
  • Voltage, amps, plug type and refrigerant from the label.
  • Whether the unit is running now, its current reading and whether it has been tipped.
  • Gasket, door, hinge and top condition, with photos.
  • Age or serial number, and any service history you have.
  • Pickup location, floor, and door or elevator limits on your end.

List through sell used restaurant equipment. For related maintenance, see how to clean a commercial ice machine.

Sources

Dates are the revision shown on each document. Specifications can change without notice, so use the sheet for the exact unit you are buying. The Beverage-Air BB48HC-1-F-S-27 sheet is a manufacturer document hosted by a dealer.