Nitrile Glove Thickness Chart: 3, 4, 5, 6 and 8 Mil Compared

Nitrile glove thickness chart: mil to mm, published specs from named gloves, exam-grade minimums, cost per glove and surplus case checks.

By Food Service SurplusPublished 12 min read
Buyer guideCleaning & janitorial

One mil is 0.001 inch, or exactly 0.0254 mm, so a 3 mil nitrile glove is 0.0762 mm thick and an 8 mil glove is 0.2032 mm. AMMEX's glove guide puts 3 mil and under on jobs that don't need strong protection from chemicals or hazardous materials, 5 to 6 mil on general duty through heavier work, and 8 mil and up on heavy-duty use. Thicker gloves cost more and reduce dexterity. Before you compare two boxes, check where each mil rating is measured, because brands don't all quote the same spot.

Nitrile glove thickness chart

Mil Millimeters Inches Published job guidance
3 0.0762 0.003 AMMEX: jobs without a strong chemical or hazmat need. Its 3 mil cleaning examples are wiping surfaces, mopping, cleaning bathrooms and emptying trash.
4 0.1016 0.004 AMMEX's guide has no 4 mil tier. SHOWA lists 4 mil as the thickness of its 9.5 inch N-DEX 6050PF medical exam glove.
5 0.1270 0.005 AMMEX: general duty through heavier automotive or industrial work with tools and machinery.
6 0.1524 0.006 AMMEX: same 5 to 6 mil tier. It points to its 6 and 8 mil raised-texture gloves for the most demanding cleaning jobs.
8 0.2032 0.008 AMMEX: rated for heavy-duty use. PIP lists its 8 mil 50-N092B for light chemical applications, printing, and meat and poultry processing.

These are named companies' tiers, not an industry standard. The conversions are straight math from the NIST factor. Thickness also has nothing to do with fit: for sizes S to XXL, use our disposable glove size chart.

What does a glove's mil rating actually measure?

It measures one point on a glove that varies from end to end. AMMEX explains why: hand-shaped formers move down the line with the fingers pointing down, so gravity pulls the solution toward the fingertips. Once dry, the fingers are the thickest part and the wrists the thinnest. More dips add more layers.

So one headline number can hide a range, and the headline doesn't always refer to the same spot. AMMEX's blog calls its X3 a 3 mil glove, and the data sheet shows 3 mil at the palm and 4 at the finger. It calls GPNHD an 8 mil glove, and that sheet shows 7 at the palm and 8 at the finger. It describes GPNB by its 5 mil palm. SHOWA's N-DEX guide gives one figure per model without saying where it applies.

Glove Grade on sheet Cuff / palm / finger (mil) Tensile min, fresh / aged (MPa) Elongation, fresh / aged AQL
Ansell MICRO-TOUCH Blue Nitrile Exam 2.0 / 2.8 / 3.5 (typical average) 14 / over 14 500% / 400% 1.5
AMMEX X3 Industrial 3 / 3 / 4 14 / 14 500% / 400% 4.0
AMMEX ABNPF Exam 3 / 3 / 4 14 / 14 500% / 400% 1.5
AMMEX Gloveworks INPF Industrial 4 / 5 / 6 14 / 14 500% / 400% 4.0
AMMEX Gloveworks GWBEN Exam 4 / 6 / 7 14 / 14 500% / 400% 1.5
AMMEX Gloveworks GPNHD Exam 6 / 7 / 8 14 / 14 500% / 400% 1.5
PIP 50-N092B (older sheet) Not stated 0.20 mm, about 7.9 mil, location not stated 18 / 14 400% / 350% Not stated

AMMEX lists its thicknesses at ±1 mil, so a nominal 3 mil point can run from 2 to 4 mil. The tensile figures are published minimums, and AMMEX lists elongation without saying whether it is a minimum, so none of these are test results for any lot. Sheets also change, and the ones above date from different years, so ask for the current version.

Mil also doesn't tell you what's in the glove. AMMEX notes that some makers add calcium carbonate filler, which makes a glove feel and measure thicker just as added nitrile would. It also says fillers reduce shelf life and make gloves more brittle over time.

What are the ASTM D6319 minimums, and what does exam grade mean?

ASTM D6319 is the specification for nitrile examination gloves for medical use. The full text is paid and we did not read it, so we're relying on FDA 510(k) summaries that restate it. Those list a minimum thickness of 0.05 mm at both palm and finger, which is about 2 mil. They also list tensile strength of at least 14 MPa before and after aging, and elongation of at least 500% before aging and 400% after.

Compare the 2 mil floor with the table above. Exam grade is not a promise of a thick glove. AMMEX's X3 and ABNPF show the same nominal thickness with different AQL levels and different grades.

In US regulatory terms, a patient examination glove is a disposable device intended for medical purposes, worn on the examiner's hand or finger to prevent contamination between patient and examiner (21 CFR 880.6250). FDA regulates medical gloves as Class I reserved devices and says they require a 510(k) premarket notification. It describes its review as covering leak resistance, certain physical properties and biocompatibility.

Data sheets don't all state this clearly, so an exam-grade label alone doesn't answer the question. If clearance matters to your purchase, ask for the 510(k) number. Our nitrile vs vinyl guide covers what AQL means.

Does a thicker glove mean more strength, or less dexterity?

Usually some of both, though the sheets don't show it the way buyers expect.

  • Dexterity and cost: AMMEX says thicker gloves resist chemicals better but reduce dexterity, and cost more to make.
  • Chemical breakthrough: AMMEX reports that manufacturers generally state that doubling thickness quadruples a chemical's breakthrough time. Treat that as a rule of thumb, not chemical data for your product. OSHA requires employers to choose hand protection based on the task, conditions, duration of use and hazards (29 CFR 1910.138).
  • Tensile strength: The 3 mil and 8 mil AMMEX gloves above list the same 14 MPa minimum. MPa is force per unit of cross-section, so it describes the material floor rather than the whole glove. At the same MPa, more material takes more force to break.
  • Tear and cut: Most sheets we read don't rate tear at all. The exception, PIP's 8 mil sheet, lists EN 388:2001 scores of abrasion 2, cut 0, tear 0 and puncture 3. Extra mils don't turn a disposable glove into a cut-resistant one.

4 mil vs 5 mil vs 8 mil in a kitchen: which fits?

No manufacturer we found publishes a kitchen rule by mil, so this table is our reading of the guidance above. It is not a standard.

Thickness Reasonable fit Trade-off
4 mil Light prep and service where gloves change often Least durable of the three, lowest material per glove
5 mil Longer tasks, equipment maintenance and deep cleaning, which AMMEX lists for its 5 mil GPNB, along with food service and processing Less feel than a thinner glove
8 mil Deep cleaning and handling cleaning chemicals, which AMMEX lists for its heavy-duty line; PIP lists meat and poultry processing for its 8 mil glove Lowest dexterity and usually the highest cost per glove

Thickness doesn't settle two kitchen questions. The first is the dish pit: AMMEX says dishwashing gloves are generally 17 mil or more, so an 8 mil disposable is not the same product. The second is food contact, which depends on the specific glove's documentation. PIP's sheet cites food-contact rules for its 8 mil glove's component materials, and Ansell's MICRO-TOUCH sheet lists 21 CFR 177.2600, but those claims belong to those products. See are nitrile gloves food safe? before buying for food handling.

Do thicker gloves come in fewer per box?

Sometimes, but not on a fixed scale. A heavy glove in a 50-count box can look cheap if you only compare box prices.

Glove Finger (mil) Per box Per case Length Listed weight
Ansell MICRO-TOUCH Blue Nitrile 3.5 200 2,000 240 mm Not listed
AMMEX X3 4 100 1,000 240 mm 4.2 g
AMMEX Gloveworks INPF 6 100 1,000 240 mm 5.8 g
AMMEX Gloveworks GWBEN 7 100 1,000 240 mm 6.0 to 8.0 g by size
AMMEX Gloveworks GPNHD 8 50 500 305 mm 11.0 g

Note that GPNHD is also longer, so it isn't a pure thickness comparison.

Here is a worked example with made-up prices, not market data:

Lot Gloves per case Case price Cost per glove
4 mil, 200 per box, 10 boxes 2,000 $110 $0.055
5 mil, 100 per box, 10 boxes 1,000 $70 $0.070
8 mil, 50 per box, 10 boxes 500 $60 $0.120

The 8 mil case has the lowest sticker price and the highest cost per glove. It pays off against the 5 mil lot only if one glove does the work of about 1.7 (0.120 ÷ 0.070). AMMEX makes the fewer-changes case for its 5 mil GPNB, and that argument can hold for cleaning work. In food handling, changes are often set by the task rather than by wear, as our nitrile vs vinyl guide explains. Run your own numbers in the unit price calculator.

How long do nitrile gloves last in storage?

Go by the product's label, not a general rule. FDA's Medical Glove Guidance Manual (2008) says expiration date labeling on medical gloves is voluntary. If a maker claims a date, the gloves should meet their 510(k) specifications for the whole claimed shelf life. FDA will accept a provisional date of up to 3 years from manufacture based on accelerated aging, and it says dates based on real-time data should not exceed 5 years.

Published figures fit that range. Ansell lists 3 years for MICRO-TOUCH Blue Nitrile, and one FDA 510(k) summary shows a 3 year shelf life for a nitrile exam glove. AMMEX says nitrile gloves are generally safe for five years when stored properly.

On storage, Ansell says to keep gloves out of direct sunlight, in a cool and dry place, and away from sources of ozone or ignition. AMMEX says to store below 104°F (40°C), preferably at 50 to 72°F. It warns that ozone can get through packaging, and names electric motors, furnaces, air conditioners and fans as sources. A shelf beside kitchen compressors or a hot line is a poor spot for spare cases.

What should you verify when buying surplus gloves?

Food Service Surplus connects buyers and sellers. It does not inspect, test, ship or guarantee gloves, so get these answers from the seller:

  • Box label photos: brand, model, material, size, powder-free status and grade.
  • Lot and expiration date: or the manufacture date if that's all that's printed. If there's no date, ask how the seller knows the age.
  • Thickness spec and location: palm, finger or both. Ask for the data sheet for that model, not just "8 mil" in a listing.
  • 510(k) number, if claimed: look it up in FDA's 510(k) database and confirm that the device name and applicant match the box.
  • Food-contact statement, if you need one: see the food-safe checklist.
  • Sealed cases: unopened, dry and undamaged, with no brittle, sticky or discolored gloves.
  • Storage conditions: heat, sunlight, moisture and nearby motors or other ozone sources.
  • True count: gloves per box, boxes per case and quantity by size.

Browse current options under disposable gloves or the wider cleaning and janitorial category.

Seller checklist: listing gloves by thickness

  • State the mil figure and where it's measured. If the box doesn't say, quote the model number and let buyers check the sheet.
  • Photograph the front and side panels, plus the lot and date stamp.
  • Give the gloves per box. Don't assume 100, especially for heavy-duty gloves.
  • List the quantity by size, the number of cases and whether cases are sealed.
  • Describe the storage history you actually know.
  • Claim exam grade, a 510(k) or food-contact use only if the packaging or a data sheet supports it.

List extra cases through sell surplus restaurant supplies.

Sources